I want to read a long series of space-separated integers from the console. I can write a program that compiles, links, and starts to run, but the following line crashes when I enter a line of 134 characters or longer:
...
READ (*,*) (DATUM(I), I=1,DATUM_CNT)
...
(DATUM_CNT is the number of integer values in the input line;
DATUM is an integer array with dimension >= DATUM_CNT;
full source below)
Sample input:
1200 291 495 475 1095 867 28 1105 645 1211 741 559 698 1200 1100 670 1211 299 804 838 880 737 110 1018 132 140 618 504 967 584 835 909 1039 1225 934 456 432 690 181 1061 875
Result is echo of input line up to "... 586 835 90" then the following error message:
%FOR-F-ERRDURREA, error during read
unit -4 file SYS$INPUT:.;
user PC 00000847
-RMS-W-TNS, terminator not seen
%TRACE-F-TRACEBACK, symbolic stack dump follows
module name routine name line rel PC abs PC
0002B292 0002B292
0002B19F 0002B19F
00027D87 00027D87
00027830 00027830
CA002C CA002C 17 00000047 00000847
... Then the remainder of the input line is printed after a command prompt.
Console input less than 134 characters in length is handled normally. The program also works if I divide the series of integers into two input lines. Also, reading the long line of integers from an external file works as expected.
Changing my terminal width setting produces the same error.
Is there anything I can do to get a FORTRAN program to accept a longer line of input from the console?
Full program source:
PROGRAM CA002C
PARAMETER DATUM_CAP=128
INTEGER DATUM_CNT, DATUM(DATUM_CAP), I, ANSWER
WRITE (*,'('' INPUT DATA:'')')
READ (*,*) DATUM_CNT
READ (*,*) (DATUM(I), I=1,DATUM_CNT)
ANSWER = 0
DO I = 1,DATUM_CNT
ANSWER = ANSWER + DATUM(I)
END DO
WRITE (*,'(''0ANSWER:''/I)') ANSWER
END
VAX FORTRAN read from console
Re: VAX FORTRAN read from console
Use unit 5 to read and open it with a recl parameter
i.e.
PROGRAM CA002C
PARAMETER DATUM_CAP=128
INTEGER DATUM_CNT, DATUM(DATUM_CAP), I, ANSWER
open( unit=5 , recl=2048)
WRITE (*,'('' INPUT DATA:'')')
READ (5,*) DATUM_CNT
READ (5,*) (DATUM(I), I=1,DATUM_CNT)
ANSWER = 0
DO I = 1,DATUM_CNT
ANSWER = ANSWER + DATUM(I)
END DO
WRITE (*,'(''0ANSWER:''/I)') ANSWER
END
i.e.
PROGRAM CA002C
PARAMETER DATUM_CAP=128
INTEGER DATUM_CNT, DATUM(DATUM_CAP), I, ANSWER
open( unit=5 , recl=2048)
WRITE (*,'('' INPUT DATA:'')')
READ (5,*) DATUM_CNT
READ (5,*) (DATUM(I), I=1,DATUM_CNT)
ANSWER = 0
DO I = 1,DATUM_CNT
ANSWER = ANSWER + DATUM(I)
END DO
WRITE (*,'(''0ANSWER:''/I)') ANSWER
END
Last edited by joukj on Wed May 08, 2024 4:14 am, edited 1 time in total.
-
Topic author - Contributor
- Posts: 20
- Joined: Tue Oct 31, 2023 10:18 pm
- Reputation: 0
- Status: Offline
Re: VAX FORTRAN read from console
Thanks, that works!
So unit 5 is the user's terminal input? What other special unit numbers are defined in VAX FORTRAN? The VAX FORTRAN Language Reference Manual indicates that they're documented in VAX FORTRAN User Manual, but I can't find a copy on-line.
So unit 5 is the user's terminal input? What other special unit numbers are defined in VAX FORTRAN? The VAX FORTRAN Language Reference Manual indicates that they're documented in VAX FORTRAN User Manual, but I can't find a copy on-line.
-
- Master
- Posts: 235
- Joined: Sat Aug 15, 2020 9:00 am
- Reputation: 0
- Location: Cambridge, UK
- Status: Offline
Re: VAX FORTRAN read from console
Chris Townley
VMS Ambassador
VMS Ambassador
-
Topic author - Contributor
- Posts: 20
- Joined: Tue Oct 31, 2023 10:18 pm
- Reputation: 0
- Status: Offline
Re: VAX FORTRAN read from console
I found the VSI version of the User Manual, but missed this line:
"...unit number 5 is associated with SYS$INPUT and unit 6 with SYS$OUTPUT."
Are 5 and 6 the only unit numbers with such special associations?
"...unit number 5 is associated with SYS$INPUT and unit 6 with SYS$OUTPUT."
Are 5 and 6 the only unit numbers with such special associations?
Re: VAX FORTRAN read from console
5 &6 are the ones most used and are also valid for input/output on other platforms (i.e. gfortran on linux etc..)
But as you can see from your error message unit=4 seems to be associated with *
But as you can see from your error message unit=4 seems to be associated with *
Last edited by joukj on Wed May 08, 2024 10:28 am, edited 2 times in total.