problem adding a satellite to cluster
Posted: Thu Jan 04, 2024 6:19 am
Hi.
I'm running OpenVMS IA64 V8.4-L3
When try to add a satellite to a cluster I did not succeed.. I use CLUSTER_CONFIG.COM on the boot member. After creating page/swap-files on the satellites disks it waits forever telling me it waits for the satellite to reboot. On the console of the satellite I see the following message written to it every few seconds
The timezone was not specified for this node. In order toproperly
run the Time Synchronization Service (DECdts), a valid time zone rule
must be specified
What can be the problem? Does it not get the time zone from the bootmember?
Added sometime later:
I see that befote the timezone message I get
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common APPLICATION script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\APPLICATION_COMMON_CHECKSUM\
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common EVENT script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\EVENT_COMMON_CHECKSUM\
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common MOP_CLIENT script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\MOP_CLIENT_COMMON_CHECKSUM\
What the hell is going on. Why is RMISHR.EXE not installed? and hat is the checsum$checksum command?
Jouk
I'm running OpenVMS IA64 V8.4-L3
When try to add a satellite to a cluster I did not succeed.. I use CLUSTER_CONFIG.COM on the boot member. After creating page/swap-files on the satellites disks it waits forever telling me it waits for the satellite to reboot. On the console of the satellite I see the following message written to it every few seconds
The timezone was not specified for this node. In order toproperly
run the Time Synchronization Service (DECdts), a valid time zone rule
must be specified
What can be the problem? Does it not get the time zone from the bootmember?
Added sometime later:
I see that befote the timezone message I get
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common APPLICATION script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\APPLICATION_COMMON_CHECKSUM\
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common EVENT script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\EVENT_COMMON_CHECKSUM\
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common MOP_CLIENT script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\MOP_CLIENT_COMMON_CHECKSUM\
What the hell is going on. Why is RMISHR.EXE not installed? and hat is the checsum$checksum command?
Jouk