Hi.
I'm running OpenVMS IA64 V8.4-L3
When try to add a satellite to a cluster I did not succeed.. I use CLUSTER_CONFIG.COM on the boot member. After creating page/swap-files on the satellites disks it waits forever telling me it waits for the satellite to reboot. On the console of the satellite I see the following message written to it every few seconds
The timezone was not specified for this node. In order toproperly
run the Time Synchronization Service (DECdts), a valid time zone rule
must be specified
What can be the problem? Does it not get the time zone from the bootmember?
Added sometime later:
I see that befote the timezone message I get
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common APPLICATION script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\APPLICATION_COMMON_CHECKSUM\
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common EVENT script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\EVENT_COMMON_CHECKSUM\
%DCL-W-ACTIMAGE, error activating image RMISHR
-CLI-E-IMGNAME, image file BOLERO$DKA0:[SYS11.SYSCOMMON.]<SYSLIB>RMISHR.EXE
-SYSTEM-F-PROTINSTALL, protected images must be installed
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\CHECKSUM$CHECKSUM\
%NET$CONFIGURE-I-USECOMMON, using cluster common MOP_CLIENT script
%DCL-W-UNDSYM, undefined symbol - check validity and spelling
\MOP_CLIENT_COMMON_CHECKSUM\
What the hell is going on. Why is RMISHR.EXE not installed? and hat is the checsum$checksum command?
Jouk
problem adding a satellite to cluster
problem adding a satellite to cluster
Last edited by joukj on Thu Jan 04, 2024 9:55 am, edited 2 times in total.
Re: problem adding a satellite to cluster
And probably another change to get rid of the hang on the repeated timezone mesage.
Last edited by joukj on Mon Jan 08, 2024 7:28 am, edited 1 time in total.
-
- VSI Expert
- Contributor
- Posts: 17
- Joined: Sat Sep 11, 2021 10:24 pm
- Reputation: 0
- Status: Offline
Re: problem adding a satellite to cluster
re: And probably another change to get rid of the hang on the repeated timezone mesage.
Could you please post the line in STARTUP1.COM that runs NET$CONFIGURE.COM?
n.b. I'm assuming that it's there since you're getting NET$CONFIGURE messages.
It should look like:
$ @SYS$MANAGER:NET$CONFIGURE "AUTOCONFIGURE" <P2> ... <P7>
Could you please post the line in STARTUP1.COM that runs NET$CONFIGURE.COM?
n.b. I'm assuming that it's there since you're getting NET$CONFIGURE messages.
It should look like:
$ @SYS$MANAGER:NET$CONFIGURE "AUTOCONFIGURE" <P2> ... <P7>
Re: problem adding a satellite to cluster
@SYS$MANAGER:NET$CONFIGURE "AUTOCONFIGURE" "LOCAL:.TANGO" "TANGO" "" "" "" "29.62"